EngineeringSlash- The electronic projects,electronic project,electronic schematic,electronic design » Electrical circuits http://www.engineeringslash.com Engineering blog- electronic circuits , electronic projects,electronic schematic,electronic design,simple circuit and hobby circuits Tue, 09 Feb 2010 05:03:16 +0000 en hourly 1 http://wordpress.org/?v=3.3.1 Three Terminal Adjustable Regulator http://www.engineeringslash.com/power-supply/three-terminal-adjustable-regulator.html http://www.engineeringslash.com/power-supply/three-terminal-adjustable-regulator.html#comments Sun, 25 Oct 2009 10:31:07 +0000 admin http://www.engineeringslash.com/?p=29 Three terminal regulators are just right when we need a single fixed voltage. But they will be cumbersome as a hobbyist works with different voltages at different times and it becomes unwieldy to keep power supplies with a number of three terminal regulators.

Wouldn’t it be better if we have an adjustable but regulated power supply, which can cater to all the voltages we need? And we have such a wonderful device where you can continually adjust your output DC voltage. Well! It is short circuit protected, has only three terminals and all other good things. LM317

LM317

LM317T is an adjustable 3 terminal positive voltage regulator capable of supplying around 1.5 amps over an output range of 1.25 to 37 volts. It also has built in current limiting and thermal shutdown features, which makes it virtually blowout proof. This is an excellent startup project with low ripple. With an easy adjustment of regulated voltage, it can be used as power source for most of the applications in the next chapters. Pin out is given in Figure 13.

Circuit :

Three Terminal Adjustable Regulator

Rectifier part is same as shown in the earlier schematic of bridge rectifier. Transformer is changed to 18 V to get a better range of regulated voltages. 9-0-9 Transformer is used as it is difficult to get an 18 V transformer. Please change transformer rating as per your requirement and the capacitor also for higher voltage rating. It is preferable to use 2200 mfd. caps as larger value makes good, low ripple output voltage.

Pulsating DC output from the bridge is now filtered by the 2200uF capacitor and fed to TN’-put terminal (1) of LM317 regulator. The output of this regulator is varied via the ‘Adj’ pin(3) and the 5K variable resistance or preset pot meter (Rl) connected to it. The regulator uses an internal Zener diode to provide a fixed reference voltage of 1.2 volt across the external resistor R2. Hence the lower end of output voltage is limited to 1.2 volts. C2 is 47uF decoupling capacitor to filter out the transient noise. Metal tab of LM317 is connected internally to the ‘Output’ pin (2). The circuit diagram is shown in Schematic 5.

Construction

Use a small Vero board to fix all the components, cut the tracks where not required and solder the pins. Mount the LM317 regulator on a heat sink. However it can be screwed to the metal case of the enclosure box with the mica insulator and the nylon washer with the mounting screw as shown in Figure 12.

Use a little of heat sink compound on the metal tab and mica insulator as it helps to transfer heat between LM317 and case or heat sink.Use a metal box of suitable size and fix the veroboard and transformer. Mains wire is connected to the primary side of the transformer and taken out. Carefully insulate the mains joints. Mains switch is not shown in the schematic. You may add one if it is required. 5k linear potentiometer is fixed at the casing. Measure the voltages and mark them suitably on a dial fixed on the face of the casing with appropriate indication of the voltage. LED is also fixed on the casing to indicate the power supply.

Use a small Vero board to fix all the components, cut the tracks where not required and solder the pins. Mount the LM317 regulator on a heat sink. However it can be screwed to the metal case of the enclosure box with the mica insulator and the nylon washer with the mounting screw as shown in Figure 12.
Use a little of heat sink compound on the metal tab and mica insulator as it helps to transfer heat between LM317 and case or heat sink.
Use a metal box of suitable size and fix the veroboard and transformer. Mains wire is connected to the primary side of the transformer and taken out. Carefully insulate the mains joints. Mains switch is not shown in the schematic. You may add one if it is required. 5k linear potentiometer is fixed at the casing. Measure the voltages and mark them suitably on a dial fixed on the face of the casing with appropriate indication of the voltage. LED is also fixed on the casing to indicate the power supply.

Related articles

]]> http://www.engineeringslash.com/power-supply/three-terminal-adjustable-regulator.html/feed 0